The Bean SchoolShop Artisan Bean(opens in a new tab)

The guide

Cleaning and descaling

Coffee leaves a residue that goes stale and then rancid: oils on a grinder's burrs, fines in a basket, scale in a boiler, milk set hard on a steam wand. None of it is difficult to deal with, and most of it takes under a minute a day. This guide covers what to clean on each kind of brewer, how to descale a kettle and an espresso machine, what coffee oils actually do to a grinder — and, just as usefully, what is fuss.

About 16 minutes

Most cleaning advice is either so vague that it cannot be followed (“clean your machine regularly”) or so thorough that it puts you off starting. The truth is closer to the first. A rinse after every use, a proper wash once a week, a descale when your water asks for one, and a new gasket every year or two will keep almost any brewer making good coffee for a decade.

This guide is organised by the thing you own, because the jobs genuinely differ. It also says plainly which tasks matter and which are theatre, because some of the most repeated advice on the internet — baking soda as a descaler, rice through a grinder, descaling on a schedule whether or not your water needs it — is either useless or mildly harmful. Cleaning is worth doing properly and worth doing quickly, and it is not worth worrying about.

01

What the mess actually is

Four things make coffee equipment dirty, and only one of them is coffee grounds.

The first is oil. Roasted coffee contains fats and oils, and every brew leaves a film of them behind — on a basket, in a press, on a grinder's burrs. Dark roasts leave more, because roasting brings the bean's oils to the surface and a shiny bean is an oily bean. The film is the problem, not the visible grounds. Oils oxidise once they are exposed to air, and oxidised coffee oil smells of old nuts, crayon and cardboard, and tastes harsh and slightly stale in a way that no recipe can correct. That is what people mean when they say a machine has “gone off”.

The second is fines: the powdery particles that stick to everything. Dry fines in a grinder's chute or in the holes of a basket go stale within days, and they flavour the next brew the way a wet sponge left in a bucket flavours the next bucket of water. A gram of old ground coffee in the path of the water is enough to flatten a cup.

The third is scale, and it is the only one of the four that does real damage. Heating hard water precipitates calcium carbonate as rock, which insulates heating elements, narrows pipes, jams valves and confuses sensors. Our Water guide explains why it forms and what to do about your water; this guide is about removing it.

The fourth is everything biological: milk protein set hard on a hot steam wand, water left standing in a tank or reservoir, damp grounds sealed inside a press. Milk residue is a food hygiene matter rather than only a flavour one. Standing water grows a slimy or pinkish film that is usually harmless but tastes musty, and it means the tank needs washing rather than rinsing. Damp grounds in a closed brewer grow mould within a few warm days, and mould tastes of mould.

02

What actually matters, and what is fuss

Six jobs cover nearly all of it. The rest is optional, and some of it is worse than optional.

The six that matter: rinse everything that touches coffee after each use; dry the parts that stay wet; wash the parts properly once a week; get the oils out of the grinder every few weeks; descale according to your water rather than the calendar; and replace the parts that are designed to wear — gaskets, filters, water cartridges. Do those and you will not have a cleaning problem. Everything else in this guide is detail about how.

Descaling is where most people overshoot. Descalers are acids, and repeated acid through seals, gaskets and metal is harder on a machine than the scale it removes. Manufacturers' advice usually assumes hard water, and the descale light on many machines counts litres or elapsed time rather than measuring anything, so it is a prompt rather than a diagnosis. If your kettle does not fur up, your water is soft and your machine barely needs descaling at all.

The other fuss is mostly theatre: sterilising a French press with boiling water before every use; buying a proprietary cleaner for a job citric acid does for pennies; believing a moka pot must never see soap (it can, and see below); or thinking a brewer has to look new to make good coffee. What matters is the parts that touch the coffee and the water. The outside of the machine is cosmetic.

Two things that are called fuss and are not: the water tank, which is the most commonly neglected part of any machine and the one that makes a cup taste musty; and the grinder, which people clean far less often than their brewer and which affects the cup more. If you only add one habit to a rinse, brush out the grinder.

03

The daily rinse: the two minutes that do most of the work

Whatever you brew with, the same three moves at the end of a session prevent most of what this guide is about.

Rinse while it is warm. Empty the grounds into the bin rather than down the sink — grounds are a plumbing problem and they swell — then rinse the parts that touched coffee in hot water. Warm residue lifts off; cold, set residue needs soap and a brush, and the difference between a ten-second job and a ten-minute one is whether you did it straight away.

Then let it dry apart. Reassembling a press wet and putting it in a cupboard, or closing a machine's lid on a damp basket, is how mould gets a start. Leave the parts on a rack, in the air, and put them back together when they are dry. This costs nothing and it is the single most effective thing in this guide.

Then deal with the water. Empty a kettle or a machine's tank if you will not use it for a day or two, and wash the tank properly now and then rather than only refilling it. If you use a filter jug or a machine with a water filter, change the cartridge on the maker's schedule: a spent carbon filter can start putting back what it was taking out.

One caution while rinsing: rinse thoroughly. Washing-up liquid left on a basket, in a press or in a cup is one of the causes of coffee that tastes of soap, and it is a self-inflicted fault. Hot water does almost all of this work; detergent is for the weekly wash.

04

How to clean a coffee maker

A drip machine is a kettle with a filter basket attached, and it needs the same two things: the basket cleaned and the boiler descaled.

Daily, throw out the filter and the grounds, rinse the basket and the carafe in hot water, and wipe the hotplate if coffee has spilled on it — burnt-on coffee on a hotplate smells for weeks. Do not leave a wet paper filter sitting in the basket; it is where the musty smell in an old machine starts.

Weekly, wash the carafe and the filter basket properly in hot soapy water, and run a full reservoir of plain water through the machine with no coffee in it. Wash the removable water reservoir if it comes out, and dry it before refilling. Wipe the spray head or water distributor above the basket with a damp cloth, since oils collect there and drip into the next brew. On machines with a reusable mesh filter, wash that too, and scrub it with a brush — mesh holds oils the way a sieve holds flour.

Monthly, or when the machine tells you, descale it. How often that is depends entirely on your water: a hard-water area can need it every month or two, soft water once or twice a year. The signs are a brew that takes noticeably longer than it used to, a noisy or gurgling element, white crust on the basket plate, and a cup that tastes flat no matter what coffee you use.

If the machine stops brewing altogether, the honest order of suspects is: no water getting through because the reservoir valve is not seated, a blocked spray head, then scale in the boiler or a failed pump. Cleaning fixes the first three. A machine that has been descaled on schedule and still will not pump is a repair, not a maintenance job.

05

How to clean a pod machine

A pod machine's dirt is concentrated in two places: the plate that pierces the capsule, and the water tank.

Daily, run a water-only cycle with no capsule after your last cup — most machines have a button sequence for this, and it is worth learning — and empty the used-capsule bin, which is where mould starts if the pods sit there wet. Leave the lid open so the brewing chamber dries.

Weekly, remove the pod holder and the drip tray and wash them in hot soapy water. Check the maker's advice before putting them in a dishwasher, because some parts warp. Then wipe the puncture plate and the area around the needle with a damp cloth: grounds and scraps of foil collect there, and a partly blocked needle changes how the machine brews — usually by dribbling rather than flowing.

Every month or two, or when the machine asks, descale it with the product the maker specifies. Pod machines nearly all have a descale mode, and the sequence matters more than it does on a drip machine, because the water path is short and narrow and descaler left in it tastes sour. Follow the instructions including the rinse cycles, and change any water filter the machine uses on schedule.

What you cannot clean is the inside of the capsule, and that is the one honest advantage of the format: there is no wet basket of grounds sitting in the machine. The water path still scales, though, and the plate still collects, so the routine above is not optional. It is just short.

06

How to clean a French press, AeroPress or pour-over

These are the easiest things in coffee to keep clean, and the most common mistake is doing too much rather than too little.

Daily, rinse in hot water, rub the mesh of a press filter with your thumb to push the fines out, and let the parts dry apart. Knock the grounds into the bin first, not the sink.

Weekly, wash everything in hot soapy water. On a French press, unscrew the filter stack and separate the plates and the mesh — fines lodge between them, and that trapped layer is what tastes stale even when the press looks clean. On a pour-over cone, hot soapy water is enough; if it has stained, a soak in hot water with a little bicarbonate of soda lifts the stain, followed by a good rinse. A metal or gold-tone filter needs a little more: soak it in hot water with a drop of washing-up liquid and work an old toothbrush through the mesh, because a metal filter holds oils in a way paper does not. Do not scour it.

AeroPresses are the simplest of all: the chamber and plunger rinse clean, the cap and filter basket need the occasional soak, and the rubber seal on the plunger can be replaced when it starts to drag or leak. It is a cheap part and it is the only thing on an AeroPress that wears.

There is nothing here to descale and nothing much to replace, which is why these brewers last for decades. The one part worth watching is the mesh or the gasket, and both are inexpensive. If a press starts letting grounds through, the filter plates are usually loose rather than worn out — take the stack apart, check the order of the parts, and put it back together properly.

07

How to clean a moka pot

The moka pot attracts more folklore than any other brewer, and most of it is about how you must never wash it.

You can wash it. A moka pot is aluminium or stainless steel, and hot water with a soft sponge and a drop of washing-up liquid does it no harm. Rinsing only under the tap, which is the folklore, leaves a film of old oil on the underside of the top chamber and inside the funnel's column, and that film is exactly the rancid note people blame on the pot being “old”.

What you should not do is put an aluminium pot in a dishwasher, or scour it with steel wool or an abrasive cream. Both take the surface off and leave it pitted, and a pitted surface holds onto oils. Do not leave it standing in water either: aluminium oxidises and stains a dark grey. The grey patina itself is harmless and normal — it is the price of an aluminium pot, not a sign of neglect.

Daily, rinse both halves, dry them separately, and do not screw the pot back together wet. Weekly, wash it with soapy water and run a thin brush or a pipe cleaner through the funnel column and the spout, where coffee collects and no rinse reaches. Check the gasket and the filter plate while you are there.

The gasket is the part that matters. It hardens and flattens over a year or so and then leaks, which usually shows up not as a puddle but as a sputtering, weak, gurgling brew. Replacing the gasket — and the filter plate with it, if it is bent — fixes more bad moka coffee than any change of technique, and the pair costs very little.

If scale builds up inside, a short soak in a citric acid solution followed by a thorough rinse and a couple of brews with water only will clear it. Keep the soak short on an aluminium pot: acid left in contact for hours dulls and darkens the metal.

08

How to clean an espresso machine

An espresso machine has more places for coffee to hide than anything else on a kitchen counter, and it also has more of its routine built in.

Daily, flush water through the group with the portafilter out, wipe the shower screen, knock out and rinse the basket, and wipe the steam wand and give it a short purge before you drink. Milk on a hot wand sets within minutes; a blocked tip and a hardened layer on the outside are the most common reason a machine's steaming quietly gets worse.

Weekly, backflush with water if the machine supports it — a blind basket in the portafilter, a short run of the pump to push water back through the group — and soak the portafilter, basket and drip tray in hot water with a little detergent. Empty and rinse the water tank, and wipe out the tray rather than only emptying it.

Every month or so, or every few hundred shots, do a detergent backflush with a proper espresso cleaning powder, using the dose on the tub rather than a guess, and brush the group and around the gasket with a group brush. If the shower screen comes off without tools, take it off and clean behind it. Then rinse thoroughly with several backflushes of clean water, because a machine left with cleaner in it tastes of cleaner.

The consumables are meant to wear. The group gasket hardens in a year or two and then leaks or lets the portafilter sit at an odd angle, and a surprising number of “my machine lost pressure” problems are a cheap rubber ring. Shower screens clog and should be replaced rather than scrubbed forever. Machines with a water filter want the cartridge changed on the maker's count, not on taste. Super-automatics with a milk circuit need the milk side's own cleaning cycle, and skipping it is the fastest route to a machine that smells.

Espresso at home covers the shot side of the same machine — dialling in, puck prep and the faults behind most bad shots. This is the upkeep.

09

How to descale a kettle or a coffee maker

Scale is dissolved calcium and magnesium coming back out of the water as rock. Acid dissolves it; nothing else does.

Descaling is chemistry rather than scrubbing. Limescale is mostly calcium carbonate, which dissolves in acid and in nothing else you keep under the sink. Citric acid is the thing to use: a white powder sold in supermarkets, chemists and homebrew shops, cheap, almost odourless, and the active ingredient in most manufacturers' own descalers. White vinegar works too, and it is what everyone reaches for because it is already in the cupboard — but it is harsher on rubber seals and on aluminium, and it leaves the kitchen smelling of vinegar for a day. It is the second-best choice, not the wrong one.

Baking soda is not a descaler. It is a mild alkali, and scale needs an acid, so a bicarbonate soak will loosen grime and deodorise a carafe while leaving the scale exactly where it was. It is a good thing to have for stains and smells and a useless one for a furred kettle.

For a kettle: put a rough tablespoon or two of citric acid into a litre of water — the packet will give a dose, and more is not faster — heat it but do not boil it hard, leave it for fifteen to thirty minutes, pour it away, then boil fresh water twice and discard it. For a drip machine: put the solution in the reservoir, run half a cycle, switch off and leave it for ten to twenty minutes, finish the cycle, then run two full reservoirs of clean water through. Flush until the water tastes of nothing at all, because descaler left behind tastes sour and will make the next brew taste wrong.

With vinegar, many machine manuals suggest equal parts white vinegar and water, followed by two or three cycles of clean water. Follow the manual for your machine over any general advice, and do not use vinegar on aluminium at all, or citric acid in an aluminium kettle or boiler — acid attacks aluminium, and some cheaper machines have aluminium parts. That is the one place where improvising is expensive.

You can tell a kettle needs it when the element is furred white and the water tastes flat; a coffee maker gives you a slower brew, a noisier element, or white crust on the basket plate. How often is entirely a question of your water. If the kettle furs up within a few weeks, descale both every month or two; if it takes a year, do it once a year. Water explains how to find out which sort of water you have, and what to do about the water itself — which is the cheaper long-term fix.

10

How to descale an espresso machine

This is the one cleaning job where you follow the manual rather than the principle, because the wrong acid in the wrong machine is an expensive mistake.

An espresso machine is descaled through its own water path, with a solution and a sequence the manufacturer sets out: fill the tank to the mark, run the descale programme, rinse, repeat. The sequence exists because the boiler, the valves and the electronics all have to be protected, and because the solution has to be flushed out completely afterwards. Use the descaler the maker specifies, measure it as they say, and do not shorten the rinse cycles.

Manufacturers specify their own product because machines contain brass, copper, aluminium and several kinds of seal, and a strong acid left sitting against them corrodes them. It is partly upselling and it is not only upselling, and an espresso machine is not the place to improvise with vinegar from the cupboard.

Descale when the machine says to, and know what the light means. On many machines it counts litres through the boiler or elapsed time against an assumed water hardness rather than measuring scale, so treat it as a prompt rather than a diagnosis; some machines let you set the water hardness so the prompt matches reality. Beyond that, your water decides. A household with soft water may go a year or more between descales, and a hard-water household will need it often, whatever the light thinks.

More is not better here. Every descale is acid through the seals, so descaling monthly “to be safe” wears the machine rather than protecting it. The cheapest protection is not putting hard water in to begin with: a filter jug, low-mineral bottled water, or a machine filter changed on schedule costs far less than a repair, and it makes better coffee at the same time.

11

What coffee oils do to a grinder

A grinder is the one piece of coffee equipment whose dirt you cannot see, and the one where it shows up most in the cup.

Every dose leaves a film of oil on the burrs, in the chute and around the exit. On a dark roast the beans arrive already oily, so the film builds faster. The oil is not a problem while it is fresh; it becomes one as it oxidises, and oxidised coffee oil smells of old nuts, crayon and cardboard and tastes flat and slightly harsh. Grounds caught in the chute go stale within days and are pushed out into the next dose.

The effect in the cup is specific: coffee that tastes flat and faintly stale even though the bag is fresh, and — on espresso — shots that become harder to dial in because a gram or two of yesterday's coffee is in every basket. It is the most common reason a grinder seems to stop performing when nothing has broken, and it is why “the grinder needs a clean” is worth trying before “the grinder needs replacing”.

To clean it: empty the hopper, run the grinder until it is empty, unplug it, and brush out the burr chamber with the brush that came with it or a clean dry paintbrush. On most grinders the top burr carrier lifts out, which lets you brush both burrs and the chute properly. Do that every few weeks for filter coffee, more often for espresso and for dark roasts. Never wash the burrs, and keep water well away from the machine.

Running uncooked rice through a grinder is folk wisdom with a real risk attached: rice is harder than coffee, the dust is fine and abrasive, and on some grinders it can wear the burrs or jam the chute. I would not do it. Grinder cleaning tablets — grain-based, made to absorb oils as they pass through — are the product designed for the job; use the dose on the tub, then run a small amount of coffee through and throw it away.

Two last things. Burrs wear out slowly, over many hundreds of kilograms of coffee, and a dull burr set shows up as shots that are harder to dial in and less sweet than they used to be; on a good grinder a new burr set is worth it, on a cheap one it usually is not. And do not leave beans sitting in the hopper for weeks: they go stale in the light and the warmth, and the grinder gets the blame for the beans' age.

12

How to use all this

The short version: rinse everything that touches coffee after each use, dry it apart, wash the parts properly once a week, brush the grinder every few weeks, and descale according to your water rather than the calendar. Replace the gaskets, filters and cartridges when they wear. That is the whole of it, and it takes less time than reading this page.

If you want a schedule to keep: daily — rinse the brewer, empty the grounds, wipe the steam wand if you have one, leave the parts to dry. Weekly — hot soapy water on the basket, press, cone, pod holder or portafilter, a water-only cycle through any machine, and a wash of the water tank. Monthly or thereabouts — brush out the grinder, and descale if your water is hard. Yearly — a new gasket, a new filter cartridge, and a look at the parts that are meant to wear.

And the honest limit of all of it: cleaning cannot make old coffee taste fresh. A spotless machine fed stale beans makes a clean, flat cup, and much of the residue the grinder collects is the beans' own oils going off. Fresh beans, ground close to the brew, are the other half of the job — and the half that costs money.

Back to the home page — or read Brewing for the methods these machines brew and how to rinse them as you go, Espresso at home for dialling in the shots whose upkeep this page describes, Grinders for choosing the burrs you are now brushing out, and Water for why scale forms at all and how to keep it out of the kettle in the first place.